← All notes & experiments

Newton's Rings Experiment

Optics · Updated 28 September 2026

Aim. To determine the radius of curvature of a plano-convex lens using a monochromatic source of light of known wavelength.

Apparatus.

  • Sodium vapour lamp
  • Plano-convex lens of large focal length
  • Plane glass plate and a reflecting (45°) glass plate
  • Black paper
  • Travelling microscope with stand

Principle

A plano-convex lens of large radius of curvature RR is placed with its curved surface on a flat glass plate. The two surfaces enclose a thin air film whose thickness is zero at the point of contact and grows with distance from it. Light reflected from the top and the bottom of this film interferes, and because the film has circular symmetry the fringes are concentric rings – Newton’s rings.

Theory

Let tt be the air-film thickness at a distance rr from the point of contact. From the geometry of the circle (with t≪Rt \ll R):

r2=R2−(R−t)2=2Rt−t2≈2Rt⇒t=r22Rr^2 = R^2 - (R - t)^2 = 2Rt - t^2 \approx 2Rt \qquad\Rightarrow\qquad t = \frac{r^2}{2R}

The two reflected rays differ in path by 2t2t (normal incidence, air film, μ=1\mu = 1). The ray reflected at the glass plate (a reflection from a denser medium) also picks up an extra λ/2\lambda/2, so the effective path difference is

Δ=2t+λ2\Delta = 2t + \frac{\lambda}{2}
  • Dark rings: Δ=(2n+1)λ2\Delta = (2n+1)\dfrac{\lambda}{2}, which gives 2t=nλ2t = n\lambda.
  • Bright rings: Δ=nλ\Delta = n\lambda, which gives 2t=(2n−1)λ22t = (2n-1)\dfrac{\lambda}{2}.

Substituting t=r2/2Rt = r^2/2R in the dark-ring condition gives the radius of the nnth dark ring:

rn2=nλR⟺dn2=4nλRr_n^2 = n\lambda R \qquad\Longleftrightarrow\qquad d_n^2 = 4n\lambda R

where dn=2rnd_n = 2r_n is its diameter. The centre (n=0n = 0) is therefore dark.

Working formula

Using the difference between two rings, nn and mm, removes any error from not knowing exactly where the centre is (for example a speck of dust at the contact point):

R=dn2−dm24λ (n−m)R = \frac{d_n^2 - d_m^2}{4\lambda\,(n - m)}

The graph of dn2d_n^2 against nn is a straight line of slope 4λR4\lambda R, so R=slope/4λR = \text{slope} / 4\lambda.

For sodium light, take λ=5893 A˚=5.893×10−5 cm\lambda = 5893\ \text{Å} = 5.893\times10^{-5}\ \text{cm} from standard tables.

Procedure checklist

  • Clean the lens and both glass plates thoroughly.
  • Place the black paper on the base of the travelling microscope, the glass plate on it, and the lens on the plate.
  • Set the reflecting plate at 45∘45^\circ in front of the sodium lamp so a parallel beam falls vertically on the lens.
  • Focus the microscope until the rings are sharp, then adjust the reflecting plate slightly for uniform illumination.
  • Find the least count of the microscope: 1 MSD =0.05= 0.05 cm and 50 vernier divisions, so LC=0.05/50=0.001\text{LC} = 0.05/50 = 0.001 cm.
  • Bring the cross-wire to the centre, then move the microscope to one side, counting rings past the 25th.
  • Reverse the direction and set the cross-wire on the 20th, 15th, 10th and 5th dark rings, noting the reading each time.
  • Keep moving the same way across the centre and note the 5th, 10th … 25th dark rings on the other side.
  • Diameter d=x∼yd = x \sim y (left reading minus right reading).

Observations

Microscope readings: total =MSR+(VC×LC)= \text{MSR} + (\text{VC} \times \text{LC})

S.No Ring no. nn Left xx (cm) Right yy (cm) Diameter d=x∼yd = x \sim y (cm) d2d^2 (cm2^2)
1 5
2 10
3 15
4 20
5 25

Calculate dn2−dm2n−m\dfrac{d_n^2 - d_m^2}{n - m} for pairs of rings that are 10 apart (for example 25 and 15) and average them. Then plot d2d^2 (y-axis) against nn (x-axis).

Sanity check

For a lens with R≈100R \approx 100 cm in sodium light, d5≈0.34d_5 \approx 0.34 cm and d25≈0.77d_{25} \approx 0.77 cm. If your diameters are far from these values for a lens of similar curvature, re-check your readings.

Precautions

  1. The glass plate and lens must be cleaned thoroughly.
  2. The lens must have a large radius of curvature.
  3. Adjust the microscope eyepiece and the reflecting glass plate carefully.
  4. Do not disturb the ring system until the experiment is complete.
  5. Move the microscope in one direction only while taking readings, to avoid backlash error.

Result

  1. Radius of curvature of the plano-convex lens from the table: R=____R = \_\_\_\_ cm.
  2. Radius of curvature of the plano-convex lens from the graph: R=____R = \_\_\_\_ cm.

Download

Download the lab manual (PDF)

Lab manual (PDF)

Newton's Rings Experiment Download